Log Storage at Bonami.
The King-Ryder Lumber Company has two log storage ponds in one. The railroad track of the Louisiana & Pacific railway crosses this in the middle and the logs are dumped directly into the pond to the north, the road at that point running east and west just before it passes the mill. The pond to the south is used for a reserve pond, the logs being shoved in under the railway track.
This pond will all told hold 2,500,000 feet of logs.
The Saw Mill at Bonami.
A fine panoramic view of the saw mill of the King-Ryder Lumber Company is shown herewith in the illustrated story of the Long-Bell affiliated saw mill plants.
The mill comprises two band mills and one circular mill and is contained in a frame building two and one-half stories high, erected on a most solid brick foundation. The main building is 48x250 feet in area.
The new saw mill of the King-Ryder Lumber Company at Bonami contains two single cutting bands and one circular mill, all complete in every detail and of the most modern pattern.
These mills have all practical labor saving devices. The mill has a capacity of 150,000 feet of lumber daily, but runs day and night producing double that amount of lumber at the present time.
Timbers can be cut and surfaced four sides 20x30 inches by 54 feet in length or smaller.
The mill was built for durability and with a view of getting the lowest possible insurance rate.
Brick, iron and steel enter into its construction wherever practical.
The mill is provided with blast machinery to take care of all refuse.
Drying and Handling Rough Lumber.
The lumber is handled from the tail of the mill to the two stackers and to the yard sorting table.
The common lumber goes to the sorting chains, 150 feet long.
The lumber going direct to the yards is loaded on wagons by automatic power and hauled to the yards and dumped where it is wanted.
Lumber intended for the kilns goes to the stackers, where it is stacked on edge. From the stackers the lumber is transferred to the dry kilns 200 feet north by a cable run by a separate engine. The lath is also conveyed in the same way.
The dry kilns contain six rooms, each 22x104 feet in area. Five of these rooms are used for lumber and one for lath. The five rooms used for lumber will hold 300,000 feet. The one room used for lath holds 450,000 lath. The daily capacity of these six rooms is 100,000 feet of lumber and 40,000 lath.
The dry kiln rooms are equipped with Standard dry kiln automatic steam jets, two in each room. The old line insurance companies have adopted this particular kiln as their standard of excellence, holding that it is a high class model in every respect. All the walls of these kilns are built of 18-inch brick.
The rough sheds are directly west of the dry kilns, the main shed being 64x500 feet. There is a cooling shed 64x150 feet. These two sheds will hold 3,550,000 feet of lumber and contain 41,600 square feet of floor space.
The rough stock and railroad timbers are carried out at the tail of the mill and over a dock at the north end which is 250 feet long. The sizer referred to elsewhere stands between the tail of the mill and this dock. In fact, there are two docks, one 250x90 and one 36x250, so that at least 500,000 feet of rough lumber can be piled in this place. Twelve cars can be loaded at this dock at the same time.
Planing and Caring for Dressed Stock.
The plant of the King-Ryder Lumber Company, at Bonami, La., is fitted with two very remarkably fine and entirely modern, up to date planing mills.
Planing mill No. 1 is just a little south of the depot of the Kansas City Southern railway and is contained in a building 90x210 feet in area. The boiler house at the south end of planing mill No. 1 is fifty feet square, built almost entirely of brick and steel, and contains four boilers and a 24x30 Filer & Stowell rock valve engine.
The two large new planing mills were built to take care of the day and night runs of the saw mill and are furnished with very complete and up to date machinery for the manufacture of lumber finished to all patterns known to architects and builders.
The surplus shavings are handled from this planing mill by a 70-inch double Sturtevant fan. The shavings are piped to a sawdust burner 630 feet to the southeast, which is of steel construction, 230 feet long, in the form of an almost half circle and is ten feet high.
The lumber is handled from the yards, both to this planing mill and planing mill No. 2, on mule dollies from the rough lumber shed.
One of the most important features of the King-Ryder Lumber Company’s plant is the magnificent loading track, 2,500 feet long, which runs north and south along each side of the Kansas City Southern tracks and extends from planing mill No. 1 at the extreme south end of the plant on past the two dressed lumber sheds to and in front of planer No. 2. The dressed lumber sheds of the King-Ryder plant are two in number, each 150x150 feet in area, and will hold
3,000,000 feet of dressed stock in an area of 45,000 square feet.
Planing mill No. 2 is contained in a building 90x 200 feet in area and there is a boiler house 46x60 feet. The power plant consists of two boilers of 1,700-horse power. The engine is an 18x24 Atlas.
Electric Lights and Telephones.
The telephone system at Bonami is one of the most complete in use by a saw mill company. There is a private exchange located in the store of the company and with it are connected twenty-one instruments, with an instrument at almost every desk and certainly at all of the important points of the plant, in the works, in the mills, in the planing mills, yards, a connection with the office of the Hudson River Lumber Company at DeRidder, La., three miles distant, and a long distance connection with the Southwestern Telephone Company.
There are two electric light generators with a total capacity of 58-1/2 K. W. There are in commission twenty-one arc lights and 800 incandescent lights. Almost every important residence and place of business in the town of Bonami is thus lighted in a most complete way.
Machine Shops at Bonami.
The machine shop at Bonami is one of the most complete shops connected with any yellow pine manufacturing concern. It stands east of the saw mill. An interior view of this machine shop is shown in the illustrated story herewith. It is contained in a building 50x186 feet in area. Besides the regular machine shop tools it contains a car and woodworking shop, blacksmith shop etc. The machine tools consist of one 20-foot lathe, one 8-foot planer, one 18-inch shaper, one drill press, one hydraulic wheel press, one bolt cutter and threader, with all necessary smaller tools complete in every particular.
These people are prepared to rebuild locomotives in every part except the castings.
There is a complete brass foundry, where all brasses used about the plant are made.
There is room in this machine shop so that two or three locomotives might be placed therein and be worked upon at the same time without incommoding the men.
Fire Protection at Bonami.
There is a reservoir into which water runs direct from the well, which is located just southeast of the saw mill. This reservoir holds 90,000 gallons.
The force is applied by two Worthington pumps of 500 gallons a minute capacity each, which force the water to the main pipe lines and to the elevated water tank, which is seventy-six feet high and holds 43,000 gallons of water.
There is in use at Bonami 31,680 feet of water mains, or exactly six miles of piping of all kinds. There are seventy-five hydrants from which this water may be drawn at high pressure located where they will do the most good in case of any possible fire. Besides several thousand feet of hose there are two hose carts which can be rapidly put into use should a fire occur.
Selling the Lumber.
The product of the King-Ryder Lumber Company is handled almost entirely by the Long-Bell Lumber Company, of Kansas City.